手搖起道機(手搖挎頂)系手搖式起重工具,能在多種工程中擔任頂和挎的起重降升作用,是手搖力通過齒輪轉動,帶動殼體起升或下降。在卸重或下降時,左搬棘爪將搖把反向轉動,手動控制其快慢,以便更好的適用于于工廠、倉庫、碼頭、鐵路、建筑工程堆棧等領域,特別適用于移動安裝各種機器設備、機車維修、重物升降等,該產品設計合理、操作簡便、靈活可靠,對提高工作效率,減輕勞動強度起到良好的作用。
手搖起道機(手搖挎頂)系手搖式起重工具,能在多種工程中擔任頂和挎的起重降升作用,是手搖力通過齒輪轉動,帶動殼體起升或下降。在卸重或下降時,左搬棘爪將搖把反向轉動,手動控制其快慢,以便更好的適用于于工廠、倉庫、碼頭、鐵路、建筑工程堆棧等領域,特別適用于移動安裝各種機器設備、機車維修、重物升降等,該產品設計合理、操作簡便、靈活可靠,對提高工作效率,減輕勞動強度起到良好的作用。
1、要根據重物的重心選擇挎定的安放位置,起重時不至于翻倒;
2、起升及降落時必須挎板或挎腳的面積全部與重物接觸,以保證有足夠的強度以防重物滑落;
3、放置挎頂的地面應堅固,如地面較軟,應在底座下加墊塊,挎頂放在墊塊的居中位置;
4、在使用前應空搖一次,由低到高,檢查是否有卡住或異常現象,一切正常才能使用。
1.使用前必須了解重物的重量、起道機的使用范圍,嚴禁超負荷使用,以免造成設備損壞發生事故;
2.如果重物超過額定起重量,需用多臺挎頂同時操作,保持多臺挎頂負荷均勻,上升下降速度一致,保持平穩;
3、重物起升后,如果不能在短時間內卸載,則必須在重物下面填加與重物離地高度相等的輔助墊塊作為支撐。
額定最大頂重(T)5
額(e)定最大挎重(T)3
最大起重高度(mm)200
挎腳最低位置(mm)60
挎頂最高位置(mm)260
頂板最低位置(mm)520
頂板最高位置(mm)720
評分: |